Kartbook

Australian Karting Forum

Tyson Arden
  • Male
  • Nsw
  • Australia
Share
  • Blog Posts
  • Discussions (17)
  • Events
  • Groups
  • Photos
  • Photo Albums
  • Videos

Tyson Arden's Discussions

Crg rear axle hight
3 Replies

Hi im just wondering if theres a particular method to setting the rear axle hight on a crg ive only set it in otk karts that have the three holes but my crg is only one long bolt hole, the previous…Continue

Started this discussion. Last reply by vince ravese Apr 10.

Brake carrier stuck!
4 Replies

Hi has anone got any tips for removing a stuck brake carrier its on a kart i just bought and i can see its been forced on there with a hammer and chisle or screwdriver but alll the wd40 and hitting…Continue

Started this discussion. Last reply by Tyson Arden Mar 17.

Racesuit sizes
1 Reply

Hi im trying to find a good fitting racesuit problem is im abit long from waist up im 183 cm and about 70kgs so you would think an alpinestars size 54 but still feels tight to bend down, all suits…Continue

Started this discussion. Last reply by Nikola schmidt Oct 6, 2017.

Gettistarting karting again
5 Replies

Hi I am looking at getting back into karting again I used to race back in aka times in club man my question is, what class do i go for on a small budget, I've always liked the kt100s but now it's…Continue

Started this discussion. Last reply by Benno Sep 22, 2017.

 

Tyson Arden's Page

Latest Activity

Tyson Arden replied to Neville Scullion's discussion Is this forum become barren?
"Its funny years ago (2010) if you were to say bad things about the then AKA the members not AKA were the first to pull you up and i know that first hand. Having said that the rules should not be abused i was a victim of online bullying and had a…"
May 17
Tyson Arden replied to Neville Scullion's discussion Is this forum become barren?
"Great comments im sure lots agree with all of the above and take notice of whats being said"
May 17
Paul McNeil left a comment for Tyson Arden
"Tyson, on the KT1 (series 11) I found there are 2, 5mm holes on the bearing carrier that either a 5mm bolt or 5mm rod can be used to go through the frame where the bearing carriers bolt to it. This is the middle…"
Apr 10
vince ravese replied to Tyson Arden's discussion Crg rear axle hight
"I've always had mine set low, axle up. It's what crg recommend in normal dry conditions. I have tried high, but kart did not respond well. Never tried middle."
Apr 10
Tyson Arden replied to Tyson Arden's discussion Crg rear axle hight
"Its a kt11 chassis, i ended up setting it up where it was in the middle/upper position kinda using the old bolt marks and used a ruler to get it where i hope its right... If its only meant to be either up or down id like to know because ive done it…"
Apr 9
vince ravese replied to Tyson Arden's discussion Crg rear axle hight
"i always assumed it was a 2 setting adjustment, either up or down. Otherwise pretty hard to get axle height same both sides, can be done though. What chassis?"
Apr 9
Tyson Arden replied to Tyson Arden's discussion Brake carrier stuck!
"On the other hand i might cut as it would take a special kind of idiot to put that carrier back on anything"
Mar 17
Tyson Arden replied to Tyson Arden's discussion Brake carrier stuck!
"Thanks mate i got the key out by hitting it to the right ill upgrade screwdrivers and try again"
Mar 17
Neville Scullion replied to Tyson Arden's discussion Brake carrier stuck!
"If the key is bent, and the carrier is already damaged, might be easier to cut through and discard, otherwise, removed the caliper and hit the carrier back away from the end of the key that is bent (upwards?), until you can remove the key. By…"
Mar 17
Tyson Arden replied to Tyson Arden's discussion Brake carrier stuck!
"Its on a crg kt11 so i cant get the axle out untill this carrier is off, ive undone all the grub screws so the axle moves free so im trying to hold it from sliding side and bash the carrier off, (with a busted shoulder) should i tighten grub screws…"
Mar 16
Tyson Arden replied to kris centofanti's discussion Is there any interest in the senior four strokes
"Yes i used both racing sportsman sa with the 100 S, i really couldnt afford to race but this happens, i used one set of sl1s for about four race meetings and a few test days between as well and to be honest not sure of lap time fall off i diddnt…"
Dec 30, 2017
Tyson Arden replied to kris centofanti's discussion Is there any interest in the senior four strokes
"Sorry for the sarcasm but to serious what tyre wont need to be replaced for every race meeting? even the dunlop sl1s were replaced every meeting, i dont want to drive around on rocks and still have to buy new tyres every race."
Dec 29, 2017
Tyson Arden replied to kris centofanti's discussion Is there any interest in the senior four strokes
"As long as theres super light, light, medium light, medium, medium heavy, heavy, super heavy, just dont want to see too many karts on track at once"
Dec 29, 2017
Tyson Arden replied to Nikola schmidt's discussion CRG SEAT IN AN OTK KART
"DONT! what will happen? The end of the world(clarkson voice) its like putting a puppy in the microwave wearing a tin foil hat while eating chocolate....BAM its over end of world..your fault"
Nov 28, 2017
Nikola schmidt replied to Tyson Arden's discussion Racesuit sizes
"You really just have to find what's "best", you'll never really get a perfect fit"
Oct 6, 2017
Benno replied to Tyson Arden's discussion Gettistarting karting again
"That kart will be fine mate and no issues if you want to run AKRA and KA.  KA want as many licence as holders as possible. They won't discriminate against someone who has raced in another series. "
Sep 22, 2017

Profile Information

My involvement in karting:
I (or my child) want to start karting
My race number:
68
My best results:
4th

Comment Wall (1 comment)

You need to be a member of Kartbook to add comments!

Join Kartbook

At 12:41 on April 10, 2018, Paul McNeil said…

Tyson, on the KT1 (series 11) I found there are 2, 5mm holes on the bearing carrier that either a 5mm bolt or 5mm rod can be used to go through the frame where the bearing carriers bolt to it. This is the middle position. Right down or up are the other 2 positions.

 
 
 

Photos

  • Add Photos
  • View All

© 2018   Created by Col Fink.   Powered by

Badges  |  Report an Issue  |  Terms of Service